Sidetracked again, this time added a drawing table drawer
RichC | November 18, 2018
This content is restricted.
Archive: Kitchen range delivered and a few other condo updates
RichC | May 29, 2018
Spent a little more time working on the condo kitchen over a stretched Memorial Day weekend since a replacement range needed to be received (gas version was shipped by mistake on first order). Thankfully was also able to get the templates made for the countertops after adding the stub wall support and some final cabinet […]
A snowy winter day, a warm fire and distractions
RichC | December 10, 2017
The first cold snowy winter day was the perfect time to fire up the woodstove in the poolhouse garage … unfortunately the distraction of a warm fire lead to other distractions and keeping me from the day’s list of projects. Instead of finishing the Corbett Christmas letter, updating the mailing list, decorating and working on […]
Start one project and sidetracked to another
RichC | August 6, 2017
While drilling a couple of precision holes, I notice the relatively new larger drill press table extension wiggled out of position if it was bumped. The problem was that it was designed to clamp to the small steel table that comes with most tabletop and floor stand drill presses. To correct I added a scrap […]
Throwback Thursdays and my life with woodstoves #TBT
RichC | January 19, 2017
Heating with wood is in my genes, since my parents started heating with wood back when we lived on Lake Erie and were constantly without heat either due to power outages in the rural area we lived, floods forcing the power company to turn off utilities or the old finicky oil burner furnace (think “Christmas […]
Tool Tips: Screwdriver hacks [video]
RichC | January 13, 2017
A few of these screwdriver hacks are not necessarily new, but could be helpful if you are ever caught shorthanded for the right tool. I’m particularly fond of using the wrench and screwdriver together (above left) as even with a full set of wrenched and sockets, there are a few oddities preventing wrenches from […]
Tidbit how-to tip: Use a clothespin to help hold a small nail
RichC | September 20, 2016
Here’s a last minute blog filler for those who have ever (or might) hit their fingers when hammering in a small nail or tack. For years I’ve used needle-nose pliers to hold the nail, but since we have a bunch of extra "bag clips" (it is what we primarily use clothespins for) laying around, I […]
Two more florescent to LED replacements – shoplight this time
RichC | May 15, 2016
After having success in replacing a couple less expensive warm white 2 foot florescent light tubes with LED tubes the other day, I opted to order a couple 4 foot LED tubes to replace my failing "cheap" shoplights over my garage workbench (eBay $22 w/shipping). I often leave this light on 24 hours a […]
Dry-stack brickwork for woodstove continues
RichC | December 7, 2015
After fastening aluminum angle to the floor and leveling the corner with sand, I packed and filled the base with brick to continue adding our old catalytic woodstove to the shop. Then it was time to start the dry-stack walls … until I ran out of spare brick. Thankfully the brick is available so should be […]
Finally added the corner desk area to my workbench
RichC | November 24, 2015
After cleaning out the garage workshop to prepare for my woodstove addition, I removed the drawing table/desk area that I added when I was building the Sonex airplane (no longer needed since selling my project). The desktop was almost a perfect fit for the corner area in my basement workshop so I put it in […]
Woodworking: The best material for a table saw throat plate
RichC | December 18, 2013
When needing to make precise cuts or dadoes on the table saw, I have found that making them from the marine material Starboard is the best (shop around for price). Most likely the experts in woodworking have found other stock that would just as well, like the self-healing cutting board material, but since I had […]
Sharing tips for loosening Rusty Nuts
RichC | April 2, 2013
Here’s a tip posted by Lee Jennings titled “Rusty Nuts.” Excellent tips although mine is a repost of a repost. I ran across this a while ago in a post from the (Twin City DX Association) The info could prove useful the next time you run across an “impossible to loosen” nut on a […]
Seminar, workshop and networking for Taylor
RichC | January 7, 2013
My travel schedule this week was modified slightly to include a couple more cold calls in the Cleveland area that I’ve been putting off until the new year … not really my choice … but it works out so that my son Taylor will be able to go to a seminar and workshop while he […]
Enjoying a home project on Palm Sunday afternoon
RichC | March 28, 2010
I’ve been tinkering in the workshop this afternoon and hopefully my wife will be pleased that I finally finished recovering a couple chairs. They’re not antiques or anything special, but the 1952 classic petite dinning room outfit will look a bit nicer when and if my daughter or son need them for their first home. […]
Desultory - des-uhl-tawr-ee, -tohr-ee
- lacking in consistency, constancy, or visible order, disconnected; fitful: desultory conversation.
- digressing from or unconnected with the main subject; random: a desultory remark.