RichC | December 12, 2021
After years of collecting a variety of tools and “tool” parts (bits, blades, etc), I’ve noticed that the mish-mash of storage containers have become even more interesting as the actual items being stored and saved (click photos for larger). Here are a few photos with a variety of storage items in a Where’s Waldo (or […]
RichC | November 6, 2021
The Ridgid brand of cordless tools have been my choice for the home workshop for a few years now and until this past week I have had a positive experience. Earlier this year Ridgid even replaced a couple failing batteries under the LSA (Lifetime Service Agreement) … BUT now this brand of choice is a […]
RichC | August 11, 2021
Generally we (really just me) eat up the bananas before they go too soft or brown, but when they do, I make banana bread. Slowly but surely I’ve been tweaking my recipe (below) … usually adjusting the amount of bananas (and how soft) and the 1/2 – 3/4 cup of sugar part. This past week, […]
RichC | August 3, 2021
Weather and years (and abuse) has pretty much destroyed the gate, hinges and latches that I took off of the gate. I disassembled it in anticipation of our driveway project (I’m still waiting – they were delayed). The final disassemble and hauling to the back was on my weekend list, but I did not anticipate […]
RichC | July 18, 2021
Good news and bad news. First, my relatively new (2018) smaller Ridgid tool battery will not hold a charge for very long … which has been my gripe with all previous battery powered “cordless” tools, especially those prior to Lithium Ion. Actually my complaint was not with the batteries, but the pricing of replacement batteries. […]
RichC | May 27, 2021
When I come across an item that interest me in woodworking, I either try to write them down, take a photo or save the plans. In this case the idem is a simple shop helper … a table saw push stick, of which I have many … BUT, I really like the simple curves and […]
RichC | May 13, 2021
A big thank you to my son Taylor for the Amazon gift card for my birthday last week. When he asked me what I was going to buy with it, I didn’t immediately have an answer … now I do … so I’ll now post a couple new woodworking workshop items that I’m using it […]
RichC | May 5, 2021
This content is restricted.
RichC | April 24, 2021
There’s not much a tools and gadget guy like me likes more than getting something new for my workshop. After breaking a bit in my cheap-ish countersink a few weeks ago (probably imported from China), I opted for a new Montana Brand Tools which are a USA-made set rather than just buying a new cheap […]
RichC | April 8, 2021
This content is restricted.
RichC | March 27, 2021
This past week was an on and off work week. I’ve been struggling to update software and the latest Linux flavor on an old server while telling myself “I’m getting too old for this.” Right or wrong attitude, I think keeping up with fast-paced technology change is a young person’s game. On the plus side, […]
RichC | March 9, 2021
While finishing up a small black walnut book stand or bookholder for my son’s birthday later this spring, I decided to archive a photo since Taylor doesn’t regularly read my blog (watch this be the exception). I wanted to make something for him since the granddaughters usually get most projects. He is also the other “sailboat” […]
RichC | February 24, 2021
After setting up my router for better, cleaner and easier woodworking dados last week, I started thinking about something better than using my table saw’s stock miter gauge for making “coping” style end cuts on the router table. Beside a $220 commercial Coping-Jig (left), there are hundreds of homemade plans on the Internet to do […]
RichC | February 20, 2021
The weather has been … well, wintery and I’ve been working on a self-designed prototype desktop bookshelf or bookstand with the thought of making a couple of them. Unfortunately desks … let alone books … are disappearing as a Future of Everything WSJ article mentioned this past year. The design is relatively simple in that […]
RichC | February 16, 2021
It is time for a little more research on better dust and chip control in my basement workshop. Brenda can deal with the noise and giving me a place to escape, but she is not fond of the dust that makes its way upstairs – those with basement woodworking workshops know what I mean. I’ve […]
RichC | February 10, 2021
We received a surprise snowfall on Monday night this week and it caught most of us, including the weather people and snowplows off-guard. Brenda worked until close in Oxford, Ohio and it took her nearly an hour and a half to drive home .. no salt on the roads and very few snowplows were out. […]
RichC | February 6, 2021
Now that I have my new DeWalt DW735x planner working (and stored) in the pool detached garage with my ShopVac, I’ve been contemplating a better "chip separator" so that the filter doesn’t plug up so fast. I’d love to have a bigger system, but really just need to build my own cyclone separator with a […]
RichC | January 30, 2021
My basement woodworking shop is a dust-making mess in our house, but there isn’t much I can do about it now other than to improve how I collect and filter and keep dust from gravitating into the furnaces cold air returns and upstairs. In our previous house in Hudson Ohio, I was fortunate to have […]
RichC | January 20, 2021
It is common when woodworking on a bench to use some kind of vise or clamp to hold down a work piece. For longer boards I’ve always used either a couple of clamps on each end or my home-built vise and square hardwood bench dogs. (below) BUT … I’ve envied woodworkers who have 3/4” holes […]
RichC | January 17, 2021
In keeping up with lithium battery powered tools, those of us who have married into a brand have our reasons (battery warranty in my case).In reading most of the comparison literature and write-up websites, Price and warranty aside, I would probably choose Milwaukee (and have for a couple 110 volt wired tools) as a rechargeable […]
RichC | December 25, 2020
This content is restricted.
RichC | December 24, 2020
Since I expect to be busy with our family on Christmas Eve Day, I’ll prepare a post for Throwback Thursday #TBT with a few old handsaws from my families past and asked the rhetorical question to myself: “Why do you keep old handsaws that you never use?” Actually I don’t recall really needing to use […]
RichC | December 5, 2020
About a year ago I ordered two more bottles of Titebond III wood glue online (had great success using it for a fence repair), and on a whim I added a goofy looking Titebrush glue brush. I honestly expected it to get boogered up with dried glue and that I would soon be back to […]
RichC | November 25, 2020
This content is restricted.
RichC | November 15, 2020
On one of my sailing groups, a Sailrite Ultrafeed LSZ-1 user complained that the speed controller pedal was hard to regulate. I’ve found that to be true as well. Another person made the comment that they used a piece of flexible tubing/hose that gives the pedal a little more tactile feel … so I tried […]
RichC | October 13, 2020
Thrifty or maybe frugal is the word choice that I use, but occasionally “cheapskate” might be a better fit? I’ve used a 3-speed Jet Tools Air Filtration System to clean the air in my basement woodworking workshop to reduce the amount of dust. It works reasonable well but suspect a lot of dust still makes […]
RichC | October 7, 2020
The Sailrite LSZ-1 sewing machine cart is complete and turned out great. Everything worked as planned (a rarity for me) and didn’t have to purchase anything new. The wider oak material was sitting in my stock shelf, the edge banding for the fold out table stripped from the glass top of my recently disassembled printing […]
RichC | September 27, 2020
When bragging that my latest sewing cart project had zero cost in it, I held off until the end of the post to mention that I was spending money and would post about that on Sunday. Well here it is: I bought my first planer; it’s a semi-portable DeWalt DW735, with the “X” option (extra […]
RichC | July 22, 2020
This content is restricted.
RichC | July 5, 2020
This content is restricted.
RichC | July 1, 2020
As mentioned a couple days ago, I saw a fellow woodworker using a better featherboard hold-down clamp … and after over 30 years of using my “temporary” pine featherboard … with a makeshift wedge style clamp, I finally hodgepodged a new one together. The new “hold down clamp” works just fine, but after using an […]
RichC | June 27, 2020
I’ve used the same combination of featherboards on my table saw for years (photo left). I also have a Shopsmith commercial featherboard which fits the smaller table perfectly, but it only works to hold larger sized pieces against the fence on my cabinet saw. Then there is the temporary one that I made 40 years […]
RichC | May 23, 2020
The workshop runs smother when there is “a place for everything and everything is in its place” … to quote the printer and publisher Benjamin Franklin. On the other hand, perhaps the British are not fond of a “revolutionary” like Ben and prefer to credit Samuel Smiles, Mrs Isabella Beeton or John Hacket, Bishop of […]
RichC | May 20, 2020
Several posts ago I mentioned that I was participating in the Makers Mob woodworking 6-week Scrapwood Challenge as part of the stay-at-home COVID19 orders. I can’t say that this project is anything great, but it did give me something to do in the evenings besides tweet political garbage or watch more outrage and debate from […]
RichC | May 19, 2020
As mentioned on Sunday, the delayed Amazon shipment of the Kubota fuel pump set my maintenance and repair plans back a bit, but I did get around to replacing the previously substituted fuel filter in the John Deere 330. We mostly use the old John Deere diesel tractor for trailer duty (and snowblowing), but ever […]
RichC | May 13, 2020
After shipping back the defective mini amplifier that I purchase a few weeks ago (grr!), I decided it was a nice evening for a drive in the old Mercedes Benz 300D Turbodiesel. Since I was out and needed a few gallons of diesel fuel, it seemed like a good time to fill up the jugs […]
RichC | May 12, 2020
After mentioning problems last week, the new webserver is up and running with a fresh install of Linux Ubuntu 18.04 “Bionic Beaver,” MySQL database and PHP 7.2 … well I actually decided to upgrade that to PHP 7.4 for a little better speed (who knows?) I’ve abandoned MongoDB for the time being for the Quickdex.net […]
RichC | April 23, 2020
After cutting a few miter joints earlier this month with a 45 degree jig on my table saw crosscut sled, I started to contemplate the best way to cut clean tendons and dadoes. In the past I’ve used an added fence to the stock miter gauge, but it really doesn’t do a great job. Of […]
RichC | April 15, 2020
Instead of spending time this past Easter weekend dressing,going to church and getting together with family, I spent a few more hours sanding … and sanding … and sanding. My goal is to get this old exterior black walnut door (super thick veneer over oak – see above photo) ready to take a traditional oil […]
RichC | April 11, 2020
The bookshelves have been on-again, off-again as the laborious painting and improved spring weather dictates my indoor verses outdoor activities. I did get a chance to finish the “art display area” in the center bookshelf section … and so far, so good. My plan was to create a little depth perception by bring the art […]
RichC | April 10, 2020
Last week my son Taylor and friend Jeff both sent me their “homemade” stand-up or propped up (with books) notebook computers while working from home. I suspect they aren’t the only COVID19 “stay-at-home” workers trying to come up with comfortable ways to do their jobs? I know Jeff once had a stand-up desk at work […]
RichC | April 9, 2020
Last week while continuing to s-l-o-w-l-y work on the bookshelves and painting project, in-between outdoor yard cleanup and cutting the lawn for the first time in 2020, I also used the frame cutting miter jib previously mentioned. It is amazing just how much more accurate this set-up for my table saw crosscut sled is over […]
RichC | April 6, 2020
Thought I would add a late day animated GIF to the blog … partially because these Canary alerts have become a normal annoyance by sending text message alerts and partially this cardinal is cute. Hopefully he will grow tired of “looking at himself” and find a female cardinal who he can impress! Also while sending […]
RichC | April 5, 2020
Snipped an idea for the woodworking workshop that I’m planning to add to my table saw crosscut sled .. nothing complicated, but a way to use geometry in order to make the perfect 45 degree jig for cutting frames. It is a way to use perfect squares to accurately cut the 45 degree jig. Check […]
RichC | March 29, 2020
This is a two-purpose post: A woodworking (sort of) bookshelves project archive update and shared information on a jig I made. First, the bookshelves and music room/ library painting coming along slowly. I’m bogged down with putty, sanding and painting after adding a strip light shield (wood to hide the LEDs that I’m planning to […]
RichC | March 21, 2020
The painting projects continue without a need to rush or complete anything quickly. Finished the ceiling paint, some patching and trim area and “might” paint the first coat of paint that Brenda has picked on Saturday – “Bermuda Sand” (which is more yellow than the pink sand color that comes to mind – see below). […]
RichC | March 17, 2020
This content is restricted.
RichC | March 14, 2020
It was a tiring week with the drip, drip, drip Coronavirus news and highly-reactive financial markets. Although frightening, investors rightly or wrongly responded with a selloff of historic proportions. The entire meltdown seemed more like hysteria and panic and had me wondering how our country and nation ever faced plagues, a weak economy due to […]
RichC | March 8, 2020
While planning a long overdue bookcase woodworking project, I needed to learn a little more about edge banding. Previous bookcases that I’ve made have all been solid wood and either painted (in our first and second homes) or stained and poly finished oak (several book, CD, video and DVD case). This planned project is a […]
RichC | March 1, 2020
This content is restricted.
RichC | February 18, 2020
Here’s a Twofer Tuesday archive from a couple weekend photos on my phone: First, I tried to use Brenda’s grandfather’s handmade, and well worn, antique miter box to cut a couple pieces of trim .. but ended up using my powered Hitachi sliding miter saw to clean up the cut instead (I did use his […]
RichC | February 16, 2020
Although one could spend all day or night watching YouTube advice videos from expert woodworkers, I’ve limited my viewing to a few guys. I’m fond of Jon Peters for both the quality of his videos and for the short “focused” tips. In a recent YouTube video, he points out how often he finds himself using […]
RichC | February 4, 2020
This content is restricted.
RichC | February 1, 2020
I’ve used tape measures for decades both when working in construction (summer job) and for hundreds of home improvement projects .. YET never really knew why the 19.2" on center diamond mark was on tapes. Most building codes mandate that studs be spaced 16 inches apart, so the tape will help you stay on the […]
RichC | January 23, 2020
It has taken years, but I’ve finally decided to move my woodworking bench dogs from the tool tray (see below). A bench dog is an accessory used on a woodworking workbench to allow clamping of wooden items while being worked or planed. Ever since building my work table and vices with bench dogs back in […]
RichC | January 4, 2020
This content is restricted.
RichC | December 28, 2019
Instead of cleaning the workshop as I was planning, I ended up sidetracked. Nothing new about that. Since each time I pull the plywood box full of “short cuts and scraps” out from next to the miter saw, it is as if I’m dragging a 100 pound box with sandpaper on the bottom across the […]
RichC | December 10, 2019
After posting a photo of a table saw crosscut sled a couple weeks ago, I finally decided to finish the one I had been planning. In part because I had some extra 1/2” white finished plywood (I didn’t want to use the heavier 3/4”) and in part because I needed to cut a bunch of […]
RichC | November 27, 2019
When we remodeled our kitchen in the spring of 2017, I disconnected the 40 amp 220 volt electric range that we originally had in the island, and dropped the capped wires through the floor and ceiling of my basement workshop. My intention was to eventually “drop” a 220 volt line so I would have a […]